2 - 363
R2 (HIGH
COP
)
9. OPTIONAL PARTS
YKB/YLM 2nd
MEE15K022
9-2. OUTDOOR TWINNING KIT
The following optional Outdoor Twinning Kit is needed to use to combine multiple refrigerant pipes. Refer to the chapter entitled
System Design Section for the details of selecting a proper twinning kit.
High-pressure twinning pipe
Low-pressure pipe twinning kit
CMY
-ER100VBK-A
ø28.58
ø28.58
ø22.2
ø22.2
ø28.58
ø28.58
ø22.2
ø19.05
ø22.2
ø25.4
ø19.05
ø25.4
ø19.05
ø19.05
<Elbow pipe(Accessory)>
<Accessory> Fixing
screw
……
1
Pipe
cover
……1
Cable
tie
……2
Insulation
cover……1
Buffer
……1
(Outside diameter)
(Outside diameter)
<Pipe for routing through the front (Accessory)>
(Outside diameter)
<Pipe for routing through the bottom (Accessory)>
50
50
36
36
80
35
100
7
3
0
407
17
117
146
35
62
303
55
182
100
±15°
high-pressure side
Slope of the twinning pipe is at an angle
within ±15° to the horizontal plane.
Note 1:Refer to the figure below for the installation
position of the twinning pipe.
2:Pipe diameter is indicated
by inside diameter.
Twinning pipe on the
High-pressure twinning pipe
Low-pressure pipe twinning kit
CMY
-ER200VBK
(Outside diameter)
(Outside diameter)
(Outside diameter)
(Outside diameter)
<Elbow pipe(Accessory)>
<Deformed pipe(Accessory)>
<Deformed pipe(Accessory)>
<Pipe for routing through the front (Accessory)>
(3Pcs.)
(Outside diameter)
(Outside diameter)
Fixing screw
……1
Pipe cover
……1
Cable tie
……
2
Insulation cover
……
1
(Outside diameter)
<Pipe for routing through the bottom (Accessory)>
(Outside diameter)
(Outside diameter)
high-pressure side
Slope of the twinning pipe is at an angle
within ±15° to the horizontal plane.
Note 1:Refer to the figure below for the installation
position of the twinning pipe.
2:Pipe diameter is indicated
by inside diameter.
Twinning pipe on the
(Outside diameter)
<Accessory>
108
32
26
62
176
427
ø31.75
ø28.58
ø28.58
69
62
ø22.2
ø34.93
ø19.05
ø41.28
160
50
50
35
80
53
53
62
ø28.58
ø28.58
ø19.05
ø19.05
ø28.58
ø31.75
ø31.75
ø19.05
ø22.2
ø34.93
ø31.75
ø25.4
ø19.05
ø25.4
ø19.05
303
55
182
100
62
62
69
ø22.2
ø31.75
ø28.58
ø22.2
ø28.58
±15°
ø28.58
25
136
35
Slope of the twinning pipe is at an angle
within to the horizontal plane.
2. Use the attached pipe to braze the port-opening of the distributer.
3. Pipe diameter is indicated by inside diameter.
Note 1. Refer to the figure below for the installation
position of the twinning pipe.
Twinning pipe on the
high-pressure side
15
15
4. Only use the Twinning pipe by Mitsubishi (optional parts) .
